Welcome to www.13ic.com

LT3020CS8-7 Suppliers,LT3020CS8-7 Datasheet,LT3020CS8-7 on stock,LT3020CS8-7 price

Quick Search:	A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
Hot Product:	hot-1 hot-2 hot-3 hot-4 hot-5

LT3020CS8-7 Suppliers,Datasheet of LT3020CS8-7

LT3020CS8-7 ,information of good suppliers LT3020CS8-7 more information about parameters and datasheet of LT3020CS8-7 listed below for you to download. If you have any problem,please feel free to contact our custmer service

LT3020CS8-7 Suppliers
specified analog signal ranges, i.e., VNO = 3V to OV and OV to -3V.Leakage parameters are 100% tested at maximum rated hot operating temperature, and guaranteed by correlation at +250CWorst-case isolation is on channel 4 because of its proximity to the COM pin. Off-isolation = 2010g VCOMNNO, VCOM = outputVNO = input to off switch.Leakage testing at single supply is guaranteed by correlation testing with d ual supplies.
LT3020CS8-7 Datasheet

Note l. Regulation is measured at constantjunction temperature. Change in output voltage due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used.
LT3020CS8-7 Price

Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functionaloperation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure toabsolute maximum rating conditions for extended periods may affect device reliability.
LT3020CS8-7 on stock

Reduced testing version of the standard military quality class. This level uses theClass H screening and In-Process Inspections with a possible limited temperaturerange, manufacturer specified incoming flow, and the manufacturer guarantees (butmay not test) periodic and conformance inspections (Group A, B, C and D).
LT3020CS8-7 Pdf

Notes 1. CPD iS used to determine the dynamic power dissipation (PD in W) PD = CPD x VCC2 x fj X N +. (CL x VCC2 x fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; Vcc = supply voltage in Volts; N = total load switching outputs; * (CL x VCC2 x fo) = sum of outputs. 2. For 74HC2G08 the condition is VI = GND to Vcc. For 74HCT2G08 the condition is Vi = GND to Vcc - 1.5 V.

The LED output pins can be used to drive LED's directly, or can be used to provide status information to a net-work management device. The active state of each LED output driver is dependent on the logic level sampledby the corresponding PHY address input upon power-u p/reset. For example, if a given PAD input is resistivelypulled low then the corresponding LED output will be configu red as an active high d river. Conversely, if a givenPAD input is resistively pulled high then the corresponding LED output will be configured as an active low driver.These outputs are standard CMOS drivers and not open-drain.

LT3020CS8-7 Suppliers, LT3020CS8-7 Datasheet, LT3020CS8-7 on stock, LT3020CS8-7 price

LT3020CS8-7	TC74ACT08F	M48T35Y70MH1	CXA1106	340635	XC73108-10PG144I	700001FAEGWD V1-2	M51958A
PAN101B0I-204	LDM300-48S5	6666AN103K1	IDT23S05-1HDCG8	SN74HC08ANSRE4	74HC132DBLE	HLMP-ED55-NKKDD	FDS6992