Welcome to www.13ic.com

MC68EN302PV16 Suppliers,MC68EN302PV16 Datasheet,MC68EN302PV16 on stock,MC68EN302PV16 price

Quick Search:	A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
Hot Product:	hot-1 hot-2 hot-3 hot-4 hot-5

MC68EN302PV16 Suppliers,Datasheet of MC68EN302PV16

MC68EN302PV16 ,information of good suppliers MC68EN302PV16 more information about parameters and datasheet of MC68EN302PV16 listed below for you to download. If you have any problem,please feel free to contact our custmer service

MC68EN302PV16 Suppliers
10.0 Recommended Mounting Pad Geometries: The area under the tantalum wire nib should not be metalised on the PC board. The nib must have sufficient clearance to avoid electrical contact with other components. The width dimension indicated is the same as the maximum width of the capacitor. This is to minimize lateral movement.
MC68EN302PV16 Datasheet

In preset voltage mode, impedanices between SET andg round should be less than 100kl . Otherwise, spuriousconditions could cause the voltage at SET to exceedthe 60mV dual-mode threshold.
MC68EN302PV16 Price

INT/CMPTR Open Collector, Programmable Polarity. In ComparatorMode, unconditionally driven active any time temperatureexceeds the value programmed into the TSET register. INT/CMPTR will become inactive when temperature subse-quently falls below the THYST setting. (See Register SetandProgrammer's Model.) In Interrupt Mode, INT/CMPTR isalso made active byTEMP exceeding TSET; itis uncondition-ally reset to its inactive state by reading any register via the2-wire bus. If and when temperature falls below THYST, INT/CMPTR is again driven active. Reading any register willclearthe THYSTinterrupt. In Interrupt Mode, the INT/CMPTR
MC68EN302PV16 on stock

2. RAD HARD MAX. "S" EQUIVALENT - OPTIONAL DATA PACKAGE A. Certificate of Compliance B. Serialization Records C. Assembly Flow Chart D. SEM Photos and Report E. Preconditioning - Attributes Data Sheet - Hi-Rel Lot Traveler
MC68EN302PV16 Pdf

The VCO operates as an integrated low radiationrelaxation oscillator at double the conversion frequency. For downconversion the VCO frequency is divided-by-2 toprovide two differential square wave signals with exactly90 degrees phase difference, independent of the VCOfrequency.

1) The products are designed and produced for application in ordinary electronic equipment (AV equipment, OA equipment, telecommunication equipment, home appliances, amusement equipment etc.). If the products are to be used in devices requiring extremely high reliability (medical equipment, transport equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or operational error may endanger human life and sufficient fail-safe measures, please consult with the Company's sales staff in advance. If product malfunctions may result in serious damage, including that to human life, sufficient fail-safe measures must be taken, including the following: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits in the case of single-circuit failure2) The products are designed for use in a standard environment and not in any special environments. Application of the products in a special environment can deteriorate product performance. Accordingly, verification and confirmation of product performance, prior to use, is recommended if used under the following conditions: [a] Use in various types of liquid, including water, oils, chemicals, and organic solvents [b] Use outdoors where the products are exposed to direct sunlight, or in dusty places [c] Use in places where the products are exposed to sea winds or corrosive gases, including C12, H2S, NH3, S02, and N02 [d] Use in places where the products are exposed to static electricity or electromagnetic waves [e] Use in proximity to heat-producing components, plastic cords, or othe flammable items [f] Use involving sealing or coating the products with resin or other coating materials [g] Use involving unclean solder or use of water or water-soluble cleaning agents for cleaning aftersoldering [h] Use of the products in places subject to dew condensation3) The products are not radiation resistant.4) The Company is not responsible for any problems resulting from use of the products under conditions not recommended herein. 5) The Company should be notified of any product safety issues. Moreover, product safety issues should be periodically monitored by the customer.

MC68EN302PV16 Suppliers, MC68EN302PV16 Datasheet, MC68EN302PV16 on stock, MC68EN302PV16 price

MC68EN302PV16	MC10H110L	VI-213-MU	W9816G6CH-7	9248AF-96	02DZ13-Y	MX29LV320ATTC-90	VI-264-CW
PAN101B0I-204	LDM300-48S5	6666AN103K1	IDT23S05-1HDCG8	SN74HC08ANSRE4	74HC132DBLE	HLMP-ED55-NKKDD	FDS6992