Welcome to www.13ic.com

SPM0103A-TL Suppliers,SPM0103A-TL Datasheet,SPM0103A-TL on stock,SPM0103A-TL price

Quick Search:	A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
Hot Product:	hot-1 hot-2 hot-3 hot-4 hot-5

SPM0103A-TL Suppliers,Datasheet of SPM0103A-TL

SPM0103A-TL ,information of good suppliers SPM0103A-TL more information about parameters and datasheet of SPM0103A-TL listed below for you to download. If you have any problem,please feel free to contact our custmer service

SPM0103A-TL Suppliers
When the value rolls over to zero, the output flip-flop is setso that the output pin is released. Thus the outputwaveform has a fixed period of 64 PWM clock cycles; itsduty cycle is determined by contents of PWMn.5 toPWMn.0 (PVn5 to PVn0).
SPM0103A-TL Datasheet

Note l: thrate 0.8mA above 70tC. Note 2: 50% duly cycle, 1ms pulse width. Derate l.6mlVoC abow 70}C.Note 3: Pulse width lps, 30Qpps.Note 4: Oerate 0.9mWPC above 700C.Nate 5: Derate 2mWPC abaw 700C.Note 6: R.H.=40~60q,h, AC/1 min.
SPM0103A-TL Price

4.5 - Inverting Smoothing Filter Output (OUT-) This pin is the inverting output of the fully differentialanalog smoothing filter. Outputs OUT+ and OUT-provide analog signals with maximum peak-to-peak amplitude 2 x VREF, and must be followed byan external two pole smoothing filter. The externalfilter follows the internal single pole switch capaci-
SPM0103A-TL on stock

AC WAVEFORMSVM = 1.5V at Vcc > 2.7VVM = 0.5V ' VCC at Vcc < 2.7VVOL and VOH are the typical output voltage drop that occur with theoutput load.Vx = VOL+ 0.3V at Vcc > 2.7VVx = VOL+ O.1VCC at Vcc < 2.7VVY = VOH - 0.3V at Vcc > 2.7VVY = VOH - O.1VCC at Vcc < 2.7V
SPM0103A-TL Pdf

Bild / Fig. 4Hochstzulassige Gehausetemperatur / Maximum allowable case temperaturetc = f(ITAVM)Strombelastung je Zweig / current load per armParameter: StromfluBwinkel / current conduction angle 0

ldle Mode In the idle mode (see Table 2), the CPU puts itself to sleep while allof the on-chip peripherals stay active. The instruction to invoke theidle mode is the last instruction executed in the normal operatingmode before the idle mode is activated. The CPU contents, theon-chip RAM, and all of the special function registers remain intactduring this mode. The idle mode can be terminated either by anyenabled interrupt (at which time the process is picked up at theinterrupt service routine and continued), or by a hardware resetwhich starts the processor in the same manner as a power-on reset

SPM0103A-TL Suppliers, SPM0103A-TL Datasheet, SPM0103A-TL on stock, SPM0103A-TL price

SPM0103A-TL	ECWU1C473JB5	74S241N	7815	UC2805D	N87C42	M50FW002-K1	ES3EA-TR
PAN101B0I-204	LDM300-48S5	6666AN103K1	IDT23S05-1HDCG8	SN74HC08ANSRE4	74HC132DBLE	HLMP-ED55-NKKDD	FDS6992